Saturday, 12 May 2012

Nozzle....

Tittle        : Definition of Nozzle

Objective : To know the function of nozzle and the characteristics.

What is nozzle??

 

A nozzle is a device designed to control the direction or characteristics of a fluid flow (especially to increase velocity) as it exits (or enters) an enclosed chamber or pipe via an orifice.
A nozzle is often a pipe or tube of varying cross sectional area, and it can be used to direct or modify the flow of a fluid (liquid or gas). Nozzles are frequently used to control the rate of flow, speed, direction, mass, shape, and/or the pressure of the stream that emerges from them.

There are many types of nozzle that was create.

1. Jet
A gas jet, fluid jet, or hydro jet is a nozzle intended to eject gas or fluid in a coherent stream into a surrounding medium. Gas jets are commonly found in gas stoves, ovens, or barbecues. Gas jets were commonly used for light before the development of electric light. Other types of fluid jets are found in carburetors, where smooth calibrated orifices are used to regulate the flow of fuel into an engine, and in jacuzzis or spas.
Another specialized jet is the laminar jet. This is a water jet that contains devices to smooth out the pressure and flow, and gives laminar flow, as its name suggests. This gives better results for fountains.
Nozzles used for feeding hot blast into a blast furnace or forge are called tuyeres.

2.High velocity
Frequently the goal is to increase the kinetic energy of the flowing medium at the expense of its pressure and internal energy.
Nozzles can be described as convergent (narrowing down from a wide diameter to a smaller diameter in the direction of the flow) or divergent (expanding from a smaller diameter to a larger one). A de Laval nozzle has a convergent section followed by a divergent section and is often called a convergent-divergent nozzle ("con-di nozzle").
Convergent nozzles accelerate subsonic fluids. If the nozzle pressure ratio is high enough the flow will reach sonic velocity at the narrowest point (i.e. the nozzle throat). In this situation, the nozzle is said to be choked.
Increasing the nozzle pressure ratio further will not increase the throat Mach number beyond unity. Downstream (i.e. external to the nozzle) the flow is free to expand to supersonic velocities. Note that the Mach 1 can be a very high speed for a hot gas; since the speed of sound varies as the square root of absolute temperature. Thus the speed reached at a nozzle throat can be far higher than the speed of sound at sea level. This fact is used extensively in rocketry where hypersonic flows are required, and where propellant mixtures are deliberately chosen to further increase the sonic speed.
Divergent nozzles slow fluids, if the flow is subsonic, but accelerate sonic or supersonic fluids.
Convergent-divergent nozzles can therefore accelerate fluids that have choked in the convergent section to supersonic speeds. This CD process is more efficient than allowing a convergent nozzle to expand supersonically externally. The shape of the divergent section also ensures that the direction of the escaping gases is directly backwards, as any sideways component would not contribute to thrust.

3.Propelling


A jet exhaust produces a net thrust from the energy obtained from combusting fuel which is added to the inducted air. This hot air is passed through a high speed nozzle, a propelling nozzle which enormously increases its kinetic energy.[
For a given mass flow, greater thrust is obtained with a higher exhaust velocity, but the best energy efficiency is obtained when the exhaust speed is well matched with the airspeed. However, no jet aircraft can maintain velocity while exceeding its exhaust jet speed, due to momentum considerations. Supersonic jet engines, like those employed in fighters and SST aircraft (e.g. Concorde), need high exhaust speeds. Therefore supersonic aircraft very typically use a CD nozzle despite weight and cost penalties. Subsonic jet engines employ relatively low, subsonic, exhaust velocities. They thus employ simple convergent nozzles. In addition, bypass nozzles are employed giving even lower speeds.
Rocket motors use convergent-divergent nozzles with very large area ratios so as to maximise thrust and exhaust velocity and thus extremely high nozzle pressure ratios are employed. Mass flow is at a premium since all the propulsive mass is carried with vehicle, and very high exhaust speeds are desirable.

4.Magnetic
Magnetic nozzles have also been proposed for some types of propulsion, such as VASIMR, in which the flow of plasma is directed by magnetic fields instead of walls made of solid matter.

5.Spray
Many nozzles produce a very fine spray of liquids.
  • Atomizer nozzles are used for spray painting, perfumes, carburettors for internal combustion engines, spray on deodorants, antiperspirants and many other uses.
  • Air-Aspirating Nozzle-uses an opening in the cone shaped nozzle to inject air into a stream of water based foam (CAFS/AFFF/FFFP) to make the concentrate "foam up". Most commonly found on foam extinguishers and foam handlines.
  • Swirl nozzles inject the liquid in tangentially, and it spirals into the center and then exits through the central hole. Due to the vortexing this causes the spray to come out in a cone shape.
Based on these types of nozzle,  gas jet and high velocity might be suitable for this project because it will increase the velocity of the gas to turn the turbine.


Friday, 11 May 2012

Material used

Tittle        : Materials to be used
 
Objective : To list the required materials for this project
 
 
There are many devices/materials used to produce electrcity for Smart-BioBin which are :
 
1. Pressure cooker
2. A gas turbine
3. D.C motor/generator
4. Battery bank
5. Converter
6. Nozzle

Based on the materials/devices above, more research need to be done for the selection of the types of each devices. The materials/devices must be matched with this project or else problems will occur.

The size of gas turbine cannot be too large because it will affects the movement of the turbine. If the size of turbine is small then it will be easy to turn but it is also depends on the amount of gas produce/pressure.

Gas pressure concept

Tittle        : Concept of Gas Pressure

Objective : To define the meaning of pressure that is related in this project


Pressure is determined by the flow of mass from a high pressure region to a low pressure region. Pressure measurements are made on the fluid states--liquids and gases.  The pressure of water on a swimmer is more noticable.

What is pressure?

PRESSURE is a force exerted by the substance per unit area on another substance. The pressure of a gas is the force that the gas exerts on the walls of its container. Pressure is a property which determines the direction in which mass flows.

Atmospheric pressure varies with height just as water pressure varies with depth. As a swimmer dives deeper, the water pressure increases. As a mountain climber ascends to higher altitudes, the atmospheric pressure decreases. His body is compressed by a smaller amount of air above it. The atmospheric pressure at 20,000 feet is only one-half of that at sea level because about half of the entire atmosphere is below this elevation.

Atmospheric pressure at sea level can be expressed in terms of 14.7 pounds per square inch. The pressure in car or bicycle tires is also measured in pounds per square inches. A car should have 26-30 lb/sq.in. and bicycle tires 40-60/sq.in.

This concept can be used for this project where it need a high pressure from the container to turn the turbine to produce mechanical energy. A pressure gauge will be installed at the container so that the value can be seen and analyze.

Monday, 23 April 2012

DC generator or DC motor?


Tittle        : Generator and Motor

Objective : To define the meaning of generator and motor


Definition of dc generator:

An electrical Generator is a machine which converts mechanical energy (or power) into electrical energy (or power). An electric generator is based on the principle that whenever magnetic flux is cut by a conductor, an e.m.f. is induced which will cause a current to flow if the conductor circuit is closed.



Definition of dc motor:

A machine that converts d.c power into mechanical power is known as a d.c motor. Its operation is based on the principle that when a current carrying conductor is placed in a magnetic field, the conductor experiences a mechanical force.


Basically, there is no constructional difference between a d.c motor and a d.c generator. The same d.c. machine can be run as a generator or motor.

From these definitions, both motor and generator can be used for this project. So, i will choose a d.c generator but it depends on the project.

Sunday, 15 April 2012

process of producing methane gas


Tittle       : How to produce gas from waste garbage?
          Objective: To produce biogas under thermophilic digestion ( 50-65˚C)


               Waste garbage will be store in a container and it will be compressed. Then, the waste will transfer to the storage where the waste needs to be blend with liquid solution. Next, the waste needs to be transfer to digester tank where it’s broken down by bacteria in the absence of oxygen and the liquid(waste) is then heated to 50-65˚C. This produces biogas (methane) which is cleaned, compressed and sent to gas storage where biogas is stored. A turbine is used to convert methane gas into electricity where the methane gas will be burn to convert the chemical bond energy of the gas to heat energy expanding the gases within the piston, driving the drive shaft and producing mechanical energy. The mechanical energy in the rotating drive shaft is then coupled into an electrical generator.




Saturday, 14 April 2012

My FYP Project


Tittle        : FYP project's name

Objective : To define about this project and to discuss generally about it.


                
                After i had seen my supervisor, i got rough idea about my project and my supervisor had given the project's name which is called " SMART-BIOBIN".

                Basically, Smart-BioBin is a special bin where it can produce energy form the waste. This bin can decompose the waste in less than a month and it through an anaerobic digestion process where biogas will produce which is methane gas. The waste used is municipal solid waste MSW which is biomass (or biogenic) materials like paper, cardboard, food scraps, grass clippings, leaves, wood, and leather products. It also includes other non-biomass combustible materials, mainly plastics and other synthetic materials made from petroleum. Then from the gas produced (methane), the gas will be converted to electrical energy and it can be used to public. Processing waste through anaerobic digesters can make the methane available for conversion to useful energy and avoid methane emissions to the atmosphere. Indirectly, this bin can reduce the methane produced from landfills to atmosphere and can protect environment from harmful gas.
 
               So, this is the project that i decided to make. I will find the previous work and background about this project and how to do it.

Friday, 16 March 2012

what is Smart-BioBin???


Smart-BioBin is a special bin where it can produce energy form the waste. This bin can decompose the waste in less than a month and it through an anaerobic digestion process where biogas will produce which is methane gas. The waste used is municipal solid waste MSW which is biomass (or biogenic) materials like paper, cardboard, food scraps, grass clippings, leaves, wood, and leather products. It also includes other non-biomass combustible materials, mainly plastics and other synthetic materials made from petroleum. Then from the gas produced (methane), the gas will be converted to electrical energy and it can be used to public. Processing waste through anaerobic digesters can make the methane available for conversion to useful energy and avoid methane emissions to the atmosphere. Indirectly, this bin can reduce the methane produced from landfills to atmosphere and can protect environment from harmful gas.