Tuesday, 11 September 2012

Temperature gauge

Tittle       : Temperature gauge
 
Objective : To show the temperature gauge that is going to be used in this project.
 
 
This is one of the equipment that is hard for me to find. Actually, i prefer to use temperature gauge sensor where it can detect temperature using sensor and i was thinking to use digital temperature gauge so it is easier to take the value. I went to several shops including car accessories shop to find this gauge but unfortunately i cannot find it. So, i just bought common temperature gauge at Ace hardware that is used for cooking.


 
 
 
 
So this gauge will be placed at the top of cover lid of the cooker to measure inner temperature. I will update the progress when this gauge is successfully construct.

Sunday, 9 September 2012

Gas regulator

Tittle        : Gas Regulator/Pressure Gauge
 
Objective : To show the gas regulator has been drilled on the cover lid of the cooker
 
 
After i bought a gas regulator to be drilled on the cooker lead, i found out it cannot be used due to some reasons. First, the gas regulator contains valve where it cannot be drilled without a socket like a gas tank in our house. So, i have to use gas pressure regulator.


 
 
 
 
Based on the picture above, the gauge is drilled on the cover lid of the cooker. So, this part is complete. Biogas will comes out from the nozzle.

Friday, 7 September 2012

Turbine

Tittle        : Turbine

Objective : To show that DC motor is connected to the blade.

 
After several trial to get perfect blade, finally i decided to sent the actual blade and motor to be drilled at welding shop beside Masjid Zakaria, gombak. I have tried to make it by own but because of the material cannot be drilled using solder and i do not have the right tools so i cannot do it. Leave it to the expert :)


 
 

 
There was a black spot in the middle of the blade due to unsuitable material used. This is not a complete turbine. I have to change the design of the blade if it is not works. 

Thursday, 6 September 2012

Motor

Tittle        : The Chossen DC Motor
 
Objective : To prove that DC motor is bought.
 
 
I had bought a dc motor at Nixie, Jalan Pasar which cost RM18.00. A 12V DC motor is a suitable for this project that will produce small value of voltage. This type of motor is common used for projects and the price is not expensive as it always been used for most of electronics equipments.
 
This is a dc motor.
 
 
 
specifications of the motor

 

This motor will be connect to the blade that is designed. Then, it will be tested and checked whether it can be used as a turbine for Smart-BioBin project.

Sunday, 2 September 2012

Homebuilt Blade

Tittle        : How to Make Blade form Tin Can

Objective : To show the process on making blade from tin can


In this project, blade is used to move shaft to drive the motor. I have to make my own blade because there is no readymade blade that is suitable for this project. The material has to be light and heat resistant because i am dealing with 50-68 degree celcius gas which is quite hot. So what i can use is
tin can which is easy to get. To make the blade, i have to used tin opener and tin cutter.


 
 


 
tin opener
 
 
tin cutter

 
this is the blade :)
 
 
 
Actually, this is my first trial. So the blade looks non-symmetry. The actual blade i will upload in next post. 
 
 

Saturday, 1 September 2012

Type of Converter

Tittle        : Type of Converter

Objective : To clarify the circuit converter


There are many type of converter. So, for this project, i will use boost converter which convert DC -DC voltage.

I had bought the components at Jalan pasar. the circuit i chose for this type of boost converter is 6V to 12V dc-dc converter using 555 timer IC. The components used for this project are:

1. R1 - 2 kilo ohms 1/4W
2.R2 - 5 kilo ohms 1/4W
3.R3 - 2.7 kilo ohms 1/4W
4.R4 - 22 ohms 1/4W
5.C1 - 220nF
6.C2 - 100nF
7.C3 - 1000uF ( higher the better) electrolytic capacitor rated 16V
8.L1 - 40 to 60 turns #20AWG in ferrite antenna bar
9.D1 - 4A rated diode or higher
10.DZ - 1N5242B or 12V zener diode (1W)
11.Q1 - TIP41C or two parallel 2N2222, or NPN transistor (min 3W power)
12.Q2 - 2N3055 or similar NPN power transistor
13.Q3 - TIP41C or 2N3055
14.555 timer IC


Below is the picture of converter circuit.


 
 
 
So this circuit is choosen to be used as a converter. But it has not be construct completely and test yet due to some problems at main part of this project (waste garbage).

Sunday, 13 May 2012

Gas Turbine?

Tittle        : Gas Turbine

Objective : To explain the used of gas turbine,


For this project, a gas turbine is used to produce mechanical energy and it will be converted to electrical energy. There are few types of gas turbine that can be used. After did some research, i found a gas turbine that is suitable for my project which is microturbine. The advantages and explanation of microturbine are shown below.

Explanation

Microturbines are becoming widespread for distributed power and combined heat and power applications. They are one of the most promising technologies for powering hybrid electric vehicles. They range from hand held units producing less than a kilowatt, to commercial sized systems that produce tens or hundreds of kilowatts.

Part of their success is due to advances in electronics, which allows unattended operation and interfacing with the commercial power grid. Electronic power switching technology eliminates the need for the generator to be synchronized with the power grid. This allows the generator to be integrated with the turbine shaft, and to double as the starter motor.
Advantages
Microturbine systems have many advantages over reciprocating engine generators, such as higher power density (with respect to footprint and weight), extremely low emissions and few, or just one, moving part. Those designed with foil bearings and air-cooling operate without oil, coolants or other hazardous materials. Microturbines also have the advantage of having the majority of their waste heat contained in their relatively high temperature exhaust, whereas the waste heat of reciprocating engines is split between its exhaust and cooling system.

However, reciprocating engine generators are quicker to respond to changes in output power requirement and are usually slightly more efficient, although the efficiency of microturbines is increasing. Microturbines also lose more efficiency at low power levels than reciprocating engines.

They accept most commercial fuels, such as gasoline, natural gas, propane, diesel, and kerosene as well as renewable fuels such as E85, biodiesel and biogas.

Microturbine designs usually consist of a single stage radial compressor, a single stage radial turbine and a recuperator. Recuperators are difficult to design and manufacture because they operate under high pressure and temperature differentials. Exhaust heat can be used for water heating, space heating, drying processes or absorption chillers, which create cold for air conditioning from heat energy instead of electric energy.

Typical microturbine efficiencies are 25 to 35%. When in a combined heat and power cogeneration system, efficiencies of greater than 80% are commonly achieved.

So, the type of gas turbine will be consider whether it is suitable or not for Smart-BioBin.